Sensors and Interfaces
Mocowi Connect has an advanced sensor set. These sensors guarantee that you maintain full control over your control.
Active GPS
Equipped with active GPS technology, Mocowi Connect gives you real-time access to GPS data, allowing you to view the current location of your vehicle, parking spots and numbers, the position on the route and the acceleration graphs on the route from a user-friendly interface.
With the Video Wall solution provided by Mocowi partners, you can project your entire fleet or divided segments and watch the current status from your operation center in real time.
4G LTE Modem Router
Mocowi Connect includes a fully equipped modem router. Similar to standard DSL modems used in homes and offices, you can use your Mocowi Connect both inside and outside the vehicle to access the Internet. You can create an Internet connection at 4.5G speed via the Sim Card that is delivered with your Connect product, designate the internet connection to use 10 different devices at the same time with the integrated WI-FI feature. The Mocowi Connect Modem with Qualcomm core enables you to take full advantage of the 4.5G infrastructure thanks to its 150 Mb/s download and 50 Mb/s upload speed.
OBDII Chipset
The OBD II standard is an automotive standard which is specified by the automobile manufacturers to provide access to technical specifications of vehicles, sensor and electronic interface information, hardware specifications, diagnostics and report information with standardized protocols. All vehicles manufactured since 1996 must comply with this standard. Mocowi Connect is fully compatible with different vehicle brands and models with advanced OBD II hardware. Thanks to this technology, you can monitor in real time the technical status of your vehicle such as Engine, ABS, ESP, ASR, Fuel, Tire sensor, observe the fuel consumption measurement, vehicle performance evaluation and fault - warning information.
With Mocowi Cloud, you can analyze OBD II data and obtain reliable, real-time Vehicle/Personnel performance data.
Battery
Mocowi Connect is designed to be used both as connected to the OBD II port and outside the vehicle. When you use the product by plugging it into the OBD II port in the vehicle, the energy requirement is supplied via the OBD II port from your vehicle's battery. When you remove the device from the vehicle, the 4200 Mah capacity battery is activated. Thus, you can use Mocowi Connect as a portable Modem - Powerbank and GPS. Mocowi Connect enables you to charge both long-term mobile modems and other mobile devices with 4200mAh Battery capacity.
When you use Mocowi Connect as mobile device, the OBDII feature is disabled. Sensors such as GPS, Gyroscope, Barometer continue to be active.
WI-FI
Mocowi Connect is equipped with high-performance Wi-Fi. Wi-Fi allows you to access the device's 4.5G internet connection with 10 different devices and use the high-speed internet. By connecting to the modem web interface via Wi-Fi, you can edit settings such as password, sim card and connection speed, view connected devices and set your data usage limits
Mocowi Wi-Fi supports different security levels. WPA-PSK AES is designated as the default security protocol.
Sensors and Accessories
Mocowi Connect has integrated gyroscope, barometer sensors and speaker. These sensors and accessories help you to check your vehicle's status on the field, analysis of environmental conditions, and send voice messages to the vehicle. With the gyroscope, it is possible to precisely determine the acceleration of the vehicle, extraordinary sliding-drifting of the vehicle and the position in the xyz axis. You can track the weather conditions at the location of the car through barometer. The built-in speaker is used with Mocowi Cloud. You can forward the pre-determined voicemail messages in your Mocowi Cloud account to the vehicle and plan special voice messages depending on time or condition.
Voice message transmission is made via internet connection. Two way voice transmission is not available. Please contact us for automatic voice messages embedded in the device that does not need internet connection.
35 V Support
Mocowi Connect works mainly in the 12-24 Volt environment. It is fully compatible with electrical systems in cars, vans, trucks, trailers and buses. Heavy-duty vehicles are protected at 35V against battery voltage fluctuations. Through the real time clock and battery level sensor available in the device, it prevents unnecessary use of battery by going to sleep mode in long-term parking of your vehicle. You can change the time to sleep through the Application or via Mocowi Cloud.
BlueTooth
Mocowi Connect has Bluetooth 4.1 and BLE (Bluetooth Low Energy) interfaces with the Wi-Fi interface. You can use the Bluetooth interface to connect to Mocowi Connect from mobile devices and pair Mocowi approved accessories (Camera, In-Car Entertainment, IOT devices, etc.).
You can access the information produced and reported by your Mocowi Connect device via Bluetooth without using your internet connection. To do this, simply download the Mocowi Connect application to your mobile device.
Connection Ports
Mocowi Connect is equipped with 1 USB Micro and 1 HDMI port. The USB Micro port is designed to charge the battery of the device and use as powerbank for charging other mobile devices. The HDMI Port allows for independent display connection.
For long-life use of the unit, use only the connection cables and accessories provided by Mocowi.
Indicators and Buttons
Mocowi Connect has led indicators for easy monitoring of connection, health and functional status of the device. These indicators show the connection status of your device to the Internet, the status of the Mocowi Cloud connection and the battery status. Red, Orange and Green LEDs reflect current status as in a typical use. The On-Off button on the device allows the device to be switched on and off if the product is used as mobile outside the vehicle. The reset button on the device is used to restart the operating system with the Hard-Reset method at the default settings.
If the Reset button is used, your device returns to factory settings and all changes made on the device are removed. This does not damage your backup information on Mocowi Cloud.
